Camera's Firmware Updates

[shanghaikid]

is updating need internt connection ?

 

[Al Herman]

Yes you will need an internet connection to perform any updates

 

[shanghaikid]

Yes you will need an internet connection to perform any updates

so there is not any offline method for update?

 

[Al Herman]

There is but its rather technical and getting the new firmware from them is a pain. They post older versions but never the latest and greatest

 

[Matheus Vicente Gomes]

I have the model escam qf508 with firmware 13.1.1.31, i received the notification to upgrade to firmware 13.1.1.32, but it always gets locked at 99%.

I did a manual reset and then upgraded to the latest firmware 13.1.1.32, it is now working.

 

[Al Herman]

Awesome

 

[Jenderalmabuk]

Actually I'm on 14.0.1.30 with same besder model. I do not notice nothing bad issue except what I wrote in the previous post (happened only one time, fortunately).

Hello can you please send me the firmware. That the best firmware for me. But now i was upgrade to 14.0.1.31. Streaming very bad

 

[Al Herman]

I don't have the firmware, you can repost asking for the administrator of the forum for it.

 

[k_den_s]

During the firmware update, turned off the lights. Now the camera does not respond to anything. The led does not blink. Help me what to do. There is a programmer CH341A. Help!

 

[k_den_s]

21.00.01.05

 

[Al Herman]

I'm not sure from your post whether the camera is now working. If not you could try a reset to default on the camera and post back with how that turns out.

 

[k_den_s]

Tried one firmware from emudem from this theme, the camera started flashing the led and went into a cyclic reboot. Give please another firmware for KH25L6436F.

 

[Vadim]

There is a camera on the GK7102 processor. Can I link to the full firmware? I will sew the CH341A Programmer. microchip flash drive for 16mb.

 

[tranky]

Salve dopo aggiornamento firmware con yoosee la mia telecamera jt-1100bw-2 da remoto non va più bene, si blocca lo streaming non va.... se sono in wifi funziona tutto perfetto.
laversione attuale è 14.0.1.31 come faccio a metterne una precedente e quale?

Hi after firmware update with yoosee my jt-1100bw-2 camera remotely no longer works, streaming is not working .... if I am in wifi, everything works perfectly.
current version is 14.0.1.31 how do I put a previous one and which one?

 

[Vadim]

Есть несколько камер рыбий глаз.
Прошивка обновилась до 24.0.0.16.
Можно ссылку на ранние прошивки?
Не могу установить пароль на RTSP!!!

 

[Digins]

to Vadim Есть опыт прошивки этих камер?
to all, where to download tools and firmware?
IPC-W63

 

[Cvazar]

Hello.
Need firmware GM8135s/GM8136s_16M. with the web interface.
The problem with the Internet, and without it after resetting the camera
configure problem.Such a firmware was, but after renewal web gone missing.

 

[araksmanyan]

Hi everyone, please help me with problem !

I buy new IP camera , that works with GK7102 (working app YCC365 )
First time camera starts normaly , I connect it to mobile application
from few hour camera disconnected from app
tried to reset to connect to app again (already delete device from app) but camera stucks (didn't react absolutely)
I contact seller , he send me firmware for gk7102 to reinstall it again
I reinstall it and al steps repeted camera works for first time and stuck again.

please tell me how can I fix problem ?

 

[celafaremo20022]

Download the latest firmware for your Yoosee cameras. Hisilicon Hi3518E firmware version: 13.0.0.96 (updated date Sept 18, 2016):
https://drive.google.com/fi...

hello, I introduce myself I am Giovanni, I had a problem in loading the firmware, now the camera does not go anymore, I think it is in a brik state, I would like to know if the photos that I have attached reflect the firmware that was posted here in this post, if yes with what procedure can I upload it? thank you very much

 

[Al Herman]

No the photo's displayed do not indicate the firmware version